Contracts Finder

3785/COMPASS/PRESS/JS/23-Press for COMPASS (Composites at Speed and Scale) Facility

University Of Sheffield

Awarded
goods
SME-friendly

This goods tender from University Of Sheffield closed on 29 Sept 2023. It was awarded to Langzauner GmbH for £3,330,000 on 1 Dec 2023. The contract end date is 19 Oct 2026. Region: Yorkshire. Procedure: Open procedure.

Contracts like this usually come back out to tender before they end.

Live now: tenders like this

Get tenders like this by email

New tenders like this one, in your inbox every morning. Starts with 14 days of Pro, no card needed.

Unsubscribe in one click. See our privacy policy.

Key details

Contracting authority
Region
Yorkshire
Location: Rotherham
Contract value
£3,330,000award value
Submissions closed
29 September 2023
Published
19 September 2023

Procurement

Contract period
20 October 2023 - 19 October 2026
3 years
Procedure type
Open procedure
CPV classifications

Description

3785/COMPASS/PRESS/JS/23-Press for COMPASS (Composites at Speed and Scale) Facility

The University of Sheffield wishes to invite tenders for a 'Press' on behalf of the Advanced Manufacturing Research Centre, Castings Group at Catcliffe, South Yorkshire.

Scope of Requirement The AMRC has recently won funding for an 'automated, large scale composites manufacturing centre', including a 'fully automated layup and consolidation cell' which will incorporate a 10.5m (length) x 3.5m (width) x 2.3m (daylight) Press.

Within the 'Fully Automated Layup and consolidation cell' the Press will sit alongside a variety of other equipment, and will be in close proximity to the following:- o High Volume Deposition Cell - including Robot arms and guide rails; o Press Heater System; o Press Injection System; o Oven Feed table.

The Press is to be used for manufacturing research into the production of large polymer composite components using several potential processes, including (but not limited to):- o Dry fibre pre-forming; o Resin Transfer Moulding (RTM); o Gap RTM/ Infusion; o Wet Compression Moulding and Compression Moulding of pre-preg.

Brief Summary of Requirements Please see G1, G2, G3, G4 and G5 for our exact technical and functional requirements, however at a high level these can be summarised as:- o The Press will have cold platens and that any heating for processing will be applied to the tooling rather than through the platens. A system of automated tool clamping, and location will need to be included within the tendered press platen package. o The Press is expected to have a stroke of a minimum of 1500mm within the minimum daylight of 2.3m. o The Press is required to have a moving lower platen that will enter and exit along the long axis from one end only. All controls and connections for the lower tool will remain active when the lower platen is fully extracted from the press. o The AMRC is looking for flexibility in the size of tooling that can be used within the Press. The maximum size of component is defined for the purpose of this specification as 10m (length) x 3m (width) x 1.5m (depth) and this will require a minimum programmable force of up to 8 bar across the entire area of that part. Cost options for an incremental increase of this force up to 20 bar are requested (if possible). o It is anticipated that the platens' size will exceed the maximum component size by approx. 0.5m in the X and Y axes (10.5m x 3.5m) to accommodate a part of 10m x 3m. To this end the tenderer is expected to recommend a suitable platen size within its proposal. o The Press must be able to control the platens in a way that allows for tools shorter than the full length to be safely used. The limits to this function must be stated within your tender response. o The Press will be expected to maintain the platens in an accurate Z plane whilst holding a full-sized tool open against a to...

Awarded supplier

Award value
£3,330,000
Award date
1 December 2023

Contact

Address
Wallis Way, Catcliffe, Rotherham, S60 5TZ
Contact name
Jamie Shaw

Identifiers

Buyer reference
IT-40-3488-3785/COMPASS/PRESS/JS/23 - AWARD
Notice ID
a6fc4e79-fcb6-4d61-9385-50e798a9b9f3-708590
OCID
ocds-b5fd17-b00c3ceb-afae-4a32-aca1-41e8add2ee8b

Explore related tenders

External ID: cf-ocds-b5fd17-b00c3ceb-afae-4a32-aca1-41e8add2ee8b • Added 4 October 2026

Get tenders like these by email

Tell us what you do and where you work. Every morning you get the new tenders that fit, from national portals and the buyer portals most services miss.

14 days of Pro, no card. Then Free unless you upgrade.